Step Plumbing Guide for Installing a Bathtub
Step Plumbing Guide for Installing a Bathtub
Blog Article
Are you trying to find insight about A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't exactly rocket science, but it does call for strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily obtainable, the job can relocate immediately; if you need to open up a wall to remove the old tub and position the new tub, the task is much harder. In either instance, the project is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and embeded in the brand-new one. Make sure you have actually qualified on your own for the work and are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to take into consideration employing one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This post will aid you install a brand-new bathtub in your washroom if you have currently bought a brand-new bathtub and don't require to change the arrangement of your previous supply of water pipes.
Your devices and material list must make up the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water. After doing so, turn on the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be rather bothersome due to the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipes. Once the supply pipes have been eliminated, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before going on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet as well as the sink. Protect the faucet in place with the producer offered backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The former kind ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the called for setting. The wood boards are handy in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the tub till the spirit level reviews degree.
To install faucets, fit the bottom of the furthest adaptable faucet port to the ideal supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the water supply and check all joints and brand-new pipework for leaks and tighten them if required. Load the bath tub and likewise examine the overflow electrical outlet and also the normal electrical outlet for leaks.
Finally, deal with the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait up until the bath tub has actually been made use of at least when as this will settle it right into its last placement.
Getting ready for the Setup
To start with, the supporting structure provided with the bath must be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to stop pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, causing the water to penetrate the wall in between the bath and the tiling, leading to problems with dampness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are offered in tubes and cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Remember to always fill up the bathtub with water before sealing, to enable the movement experienced when the tub is in usage. The sealant can split relatively early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I figured sharing that piece of content was essential. Sharing is caring. Helping others is fun. Thanks a lot for your time. Visit us again soon.
Got a leak? Call! Report this page